16CM32C Offshore Generator Set

  • Overview
  • View product Download

Engine Design


 - World-class reliability and durability
 - Incorporates years of proven component reliability and
 - durability in marine industry
 - Medium speed long-stroke engine design
 - Ideal configuration for dynamically positioned semisubmersible rigs and drillships
 - Compact cylinder head design
 - Nodular cast-iron block with integrated ducts for lubricatingoil and charge air
 - Segmental camshaft design
 - 25° tilt capability in all directions
 - Engine design based on the higher requirements of heavyfuel oil
 - High efficiency turbocharger
 - Cylinder liner, only cooled outside the engine block
 - Engine control terminal with analog instrumentation inrobust cast casing
 - Connecting rod, split off design
 - Compact module for lower valve drives and injection pumpdrives with cam followers
 - Optional Flexible Camshaft Technology (FCT)

Ease of Installation


 - Standard modular design allows for ease of installation andreduced complexity
 - Installation-friendly, due to pumps and filters installed onthe engine
 - Cooling water system with simple plug-in connections
 - Full range of factory-installed engine attachments allowscustomization and reduction in installation time

Packaging Concept


 - Assembled, tested, and validated as a package to minimizepackage vibration and maximize component life

Improved Serviceability


 - Large inspection openings allow for convenient access tocore engine internals for easier serviceability
 - Core engine components designed for reconditioning andreuse at overhaul
 - Worldwide dealer network with factory-trained techniciansmeans that parts and support are never out of reach
 - Simplified parts spectrum by using single-pipe exhaustgas ducting

Web Site

For all your petroleum power requirements, visitwww.catoilandgasinfo.com

Engine Specifications
Minimum Rating 4370.0 ekW (5460.0 kVa)
Maximum Rating 4370.0 ekW (5460.0 kVa)
Emissions IMO Tier II
Aspiration Turbocharged-Aftercooled
Engine Control Electronic
Generator Set Control Electronic
Weight 150000.0 kg (330000.0 lb)
Stroke 460.0 mm (18.1 in)
Bore 320.0 mm (12.6 in)
Displacement 592.0 L (36126.0 in3)
Dimensions
Length 12060.0 mm (474.8 in)
Height 5661.0 mm (222.9 in)
Width 3000.0 mm (118.1 in)
Capacity for Liquids
Cooling System (Engine) 1900.0 L (502.0 gal)
Lube Oil System (Refill) 10800.0 L (2853.0 gal)

Standard Equipment

  • Engine
    • Motor-driven barring gear, fitted on engine
    • Reversing contractor and push button switch with cable
    • Electronic speed setting equipment with actuator and speed pick-up
    • Emergency shutdown equipment with pushbutton, separate, formanual emergency stop
  • Engine Indicators
    • Gauge board with set liquid damped pressure gauges for:fuel, lubricating oil, fresh water, starting air, and charge air.
    • On-engine thermometers for fuel, lubricating oil, fresh water,and charge air
    • Electric remote speed indicator
    • Turbocharger and remote speed indicator
    • Exhaust gas temperature indicator
  • Control
    • Manual control on engine, including: control panel with start /stop key, speed setting device, mechanical shutdown device, change over of control functions from engine to remote control
    • Starting solenoid valve on engine, 24 V DC
    • Separate electronic speed governor
  • Monitoring for Unattended Operation
      • Lube oil pressure at full load below danger level
      • Low lube oil pressure
      • Lube oil pressure below danger level
      • Lube oil pressure prelubrication failed
      • Low fresh water pressure at engine inlet
      • Fresh water pressure at engine inlet below danger level
      • Low fresh water pressure in LT circuit
      • Low starting air pressure
      • Low control air pressure engine/shutdown air pressure
      • Low fuel pressure at engine inlet
      • High lube oil temperature at engine inlet
      • Lube oil temperature at engine inlet above danger level
      • High water temperature at engine inlet
      • Water temperature at engine outlet above danger level
      • High charge-air temperature at engine inlet
      • Detection of water in charge-air duct
      • Leak fuel level
      • Alarm contact for high differential pressure at fuel filter
      • Alarm contact for high differential pressure at lube oil backflushing filter
      • Set of thermocouples after each cylinder, before and afterturbocharger
      • Crankcase oil mist detector
      • Protection equipment designed for automatic and manual stop inputsignals, starting interlock input signals, monitoring for the wire break of the input signal units and the emergency shutdown solenoid
      • Speed recording system for overspeed, firing speed and minimumspeed
      • Start /stop logic, controlled by engine automatic start (optional)
      • Service hour counter
      • Noris alarm system, cassette type, designed for alarm inputs for theengine including exhaust mean-value monitoring equipment as wellas alarm inputs for the propulsion plant
      • Group alarm panel for the bridge and with optional andacoustical alarm equipment
  • Starting Air System
    • Separate non-return valve for the starting air pipe to the engine
  • Air Intake System
    • Air intake filter, fitted on the turbocharger
    • – Air bottles, separate
  • Fuel System
    • Separate circulating pump driven by electric motor, horizontalor vertical
    • Duplex filter with differential pressure indication
  • Exhaust System
    • Turbocharger at free end with transition nozzle (0 degrees from the vertical and away from engine), with compressor cleaning device
    • Expansion joint separate
    • Separate silencer and spark arrester, unlagged 35 dB(A)
  • Fresh Cooling Water System
    • HT pump, fitted on engine
    • LT pump, separate, vertical design, electric motor driven
    • HT thermostat, not powered and separate
    • Engine preheating equipment, fitted on base frame
  • Lubricating Oil System
    • Plate cooler, fitted on engine
    • Force pump, fitted on engine
    • Prelubrication pump, fitted on base frame, electric motor driven
    • Boll and Kirch automatic backflushing filter, separate
    • Duplex filter with differential pressure indication, separate
    • Pressure control valve, separate
    • Thermostat, not powered, separate
  • Connecting Parts – Engine
    • Set of connecting parts between flange coupling and flywheel
    • Flexible flange coupling between engine and generator
    • Base frame with flywheel guard and incorporating lube oil sump tank,for engine and generator
    • Mounting of engine and generator on the base frame
    • Set of bonded rubber rails for resilient mounting of the base frame
    • Set of flexible pipe connections
  • Tools
    • Set of tools for the engine including hydraulic tightening tools and nozzle tester
    • Set of tools for turbocharger
    • Inside micrometer for cylinder liners
    • Ruler for cylinder liner
  • Spare Parts
    • Set of engine spare parts for unrestricted operation
    • Set of spare flexible pipe connections

Enquiry Form

REQUEST A CALL BACK